Can I Install a Bath Tub Myself? Factors to Consider And Actions
Can I Install a Bath Tub Myself? Factors to Consider And Actions
Blog Article
The content which follows pertaining to Tools You Need to Install a New Bathtub is relatively captivating. Don't overlook it.
Mounting a bath tub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is also a moderately difficult task. If the old bathtub is conveniently accessible, the task can relocate easily; if you need to open up a wall surface to get rid of the old bathtub as well as position the new bathtub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub and also embeded in the brand-new one. See to it you have actually certified on your own for the job and are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed job, it is much better to take into consideration utilizing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will help you install a new bathtub in your bathroom if you have currently acquired a brand-new bathtub and don't need to alter the plan of your previous water system pipes.
Your tools as well as product list need to consist of the following:
Preparing for the Installation
Firstly, the supporting frame provided with the bath should be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final placement.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you must do is detach the water. After doing so, activate the taps to drain any water staying in the system. The process of eliminating the existing taps can be rather troublesome because of the limited gain access to that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Tub
Utilizing the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the tub up until the level reviews degree.
To set up faucets, fit the bottom of the outermost adaptable tap port to the appropriate supply pipeline by making a compression join; after that do the very same for the various other tap.
Switch on the supply of water and examine all joints as well as new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as also check the overflow electrical outlet as well as the regular outlet for leakages.
Lastly, fix the bathroom paneling as explained in the maker's instruction manual. Tiling and sealing around the bathtub must wait till the tub has actually been utilized at the very least once as this will certainly settle it right into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and also the other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in place in between the faucet and the sink. Protect the faucet in position with the supplier offered backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former type must be attached to the faucet ends first, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a rigid seal, causing the water to penetrate the wall between the bath as well as the tiling, resulting in issues with moisture as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and installations. They are offered in tubes as well as cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealer can split rather early if you do not consider this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly readily available on the marketplace. It is recommended to fit the floor tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very intrigued by Tools You Need to Install a New Bathtub and I hope you appreciated my entry. Enjoyed reading our blog posting? Please share it. Let another person locate it. I am grateful for your time. Come back soon.
Browse Website
Report this page